SolidWorks基础命令图文教程-扫描
SolidWorks扫描命令图文教程实例模型如下
http://www.ugsnx.com/data/attachment/forum/201607/05/090137r7zo7unuodxohqoo.jpgSolidWorks中绘制的模型如下http://www.ugsnx.com/data/attachment/forum/201607/05/085908kesm2nh4ki5q2vk5.png下面就开始绘制模型首先我们点击绘制草图下边的三角符号，选择下面的3d草图。http://www.ugsnx.com/data/attachment/forum/201607/05/085908u3f9lhl8ve978l93.png绘制下面3条直线，第3条线是在1、2两条线所构成平面的法线方向。http://www.ugsnx.com/data/attachment/forum/201607/05/085909oi2o82mha5ui02xz.pnghttp://www.ugsnx.com/data/attachment/forum/201607/05/085909kkkmhe3hb3rnvv53.pnghttp://www.ugsnx.com/data/attachment/forum/201607/05/085909pkhyibru7t7mmiyl.png然后约束一下尺寸http://www.ugsnx.com/data/attachment/forum/201607/05/085909g07u7qwq02bwkzwg.png再倒个圆角http://www.ugsnx.com/data/attachment/forum/201607/05/085909zeolvm7vp7hsdl4p.png接下来退出草图，然后建一个基准平面，建在长度为30的线的端点。第1、第2参考的选择如图所示。http://www.ugsnx.com/data/attachment/forum/201607/05/085909ued6qdndd8fwdfwz.png然后我们在这个基准面上绘制草图，绘制2个圆，直径分别为14和22。http://www.ugsnx.com/data/attachment/forum/201607/05/085910o3c9q3ttcqnjac3h.png然后我们就可以用扫描命令，轮廓和路径分别选择图中所示草图，打钩确认。http://www.ugsnx.com/data/attachment/forum/201607/05/090352bkvma0g50yyyv655.jpg接着我们绘制两边的法兰，我们先绘制方形的一端，主要说下4个圆的绘制，我们先绘制图中箭头所指的两条中心线，然后将图中1圆绘制在方形对角线上，经过两次镜像得到4个圆，然后约束草图，完成。http://www.ugsnx.com/data/attachment/forum/201607/05/085910jdndubr9qnf6uyra.png因为所给的草图中没给出拉伸的高度，我这边直接拉伸5mm。http://www.ugsnx.com/data/attachment/forum/201607/05/085910qbyg559e25959yln.png接着绘制另外一端的法兰，我们绘制4个圆和两条外切线，并约束各圆直径和圆心距。http://www.ugsnx.com/data/attachment/forum/201607/05/085910by5rgdyguyshr6ee.png接着绘制一条中心线并裁剪实体，将多余的线删除，得到下图所示图形。http://www.ugsnx.com/data/attachment/forum/201607/05/085910bkhqlqajh51ohrai.png镜像之后如下图所示。http://www.ugsnx.com/data/attachment/forum/201607/05/085910dpynxyeqehfptyno.png最后这里也拉伸5mm，模型绘制完成。http://www.ugsnx.com/data/attachment/forum/201607/05/085910vx6qfesrf11b4cce.png
用这方法也很方便的 ZYF269 发表于 2016-7-5 20:00
用这方法也很方便的
嗯 谢谢指教 我这边只是用实例介绍一下扫描这个命令:D
页:
[1]