分享一个用新版后处理配置器制作的三轴后处理

青春。论未来。

tombai691019 发表于 2024-6-23 15:59
看一下图片所示，和你自已的UI定义要一致。就可以和其它变量一样控制你想要输出的内容了，看一下UG自带的 ...

大佬，刀具列表输出加工时间，同一把刀的总时间怎么输出啊

tombai691019

青春。论未来。 发表于 2024-7-28 15:34
大佬，刀具列表输出加工时间，同一把刀的总时间怎么输出啊

找一下以前的帖子，记得有个大佬分享的HASS的用配置器做的后处理，他那里面有代码，好久没搞了。我都快看不明白了。我可以把代码贴出来，你自己研究一下。由于命令里有嵌套，所以不太容易看明白。
global mom_operation_info mom_operation_name_list tool_time tool_g41 TZ_time
    set TZ_time 0
    for {set a 0} {$a < [llength $mom_operation_name_list]} {incr a} {
        if {[info exists mom_operation_info([lindex $mom_operation_name_list $a],toolpath_time)] != 1}  {set mom_operation_info([lindex $mom_operation_name_list $a],toolpath_time) 0}
        if {[info exists tool_time($mom_operation_info([lindex $mom_operation_name_list $a],tool_number))] != 1}  {set tool_time($mom_operation_info([lindex $mom_operation_name_list $a],tool_number)) 0}
        set tool_time($mom_operation_info([lindex $mom_operation_name_list $a],tool_number)) [expr $tool_time($mom_operation_info([lindex $mom_operation_name_list $a],tool_number)) + $mom_operation_info([lindex $mom_operation_name_list $a],toolpath_time)]
        #set TZ_time [expr $tool_time($mom_operation_info([lindex $mom_operation_name_list $a],tool_number)) + $mom_operation_info([lindex $mom_operation_name_list $a],toolpath_time)]
        if {[info exists tool_g41($mom_operation_info([lindex $mom_operation_name_list $a],tool_number))] != 1}  {set tool_g41($mom_operation_info([lindex $mom_operation_name_list $a],tool_number)) ""}
        if {[info exists mom_operation_info([lindex $mom_operation_name_list $a],cutcom_type)] && [info exists mom_operation_info([lindex $mom_operation_name_list $a],tool_cutcom_register)] != 1 && [string match *D:$mom_operation_info([lindex $mom_operation_name_list $a],tool_number),* $tool_g41($mom_operation_info([lindex $mom_operation_name_list $a],tool_number))] != "1" } {
            append tool_g41($mom_operation_info([lindex $mom_operation_name_list $a],tool_number)) "D:$mom_operation_info([lindex $mom_operation_name_list $a],tool_number),"
        }
        if {[info exists mom_operation_info([lindex $mom_operation_name_list $a],cutcom_type)] && [info exists mom_operation_info([lindex $mom_operation_name_list $a],tool_cutcom_register)] && [string match *D:$mom_operation_info([lindex $mom_operation_name_list $a],tool_cutcom_register),* $tool_g41($mom_operation_info([lindex $mom_operation_name_list $a],tool_number))] != "1" } {
            append tool_g41($mom_operation_info([lindex $mom_operation_name_list $a],tool_number)) "D:$mom_operation_info([lindex $mom_operation_name_list $a],tool_cutcom_register),"
        }
      set TZ_time [expr $TZ_time + $mom_operation_info([lindex $mom_operation_name_list $a],toolpath_time)]
    }

青春。论未来。

tombai691019 发表于 2024-7-28 16:18
找一下以前的帖子，记得有个大佬分享的HASS的用配置器做的后处理，他那里面有代码，好久没搞了。我都快看 ...

谢谢大佬

周先森8868

楼主N能不能改成一把刀为100为单位，然后下面的工序再一个一个加，比如第五把刀N500，第五把刀有10个工序，N501-510，机台上手改程序就方便了{:biggrin:}

sunmean

支持一下！谢谢分享！

cqfcam

谢谢试一下2406能用吗

cqfcam

大佬,怎么处理的NC文件不自动保存吖,手动也保存不了

丶唯一的存在

后处理时.报错

tombai691019

丶唯一的存在 发表于 2024-9-6 18:20
后处理时.报错

把处理后报错的日志出来看看，这样子看不出什么问题。

A544

打不开